Effect of nozzle diameter on jet impingement cooling system

Click here for a simple search.
[feed] Atom [feed] RSS 1.0 [feed] RSS 2.0
 
 

Dulfharah, Nizam Memth Ali (2009) Effect of nozzle diameter on jet impingement cooling system. Faculty of Mechanical Engineering, Universiti Malaysia Pahang.

[img]
Preview
PDF (Table of content) - Accepted Version
188Kb
[img]
Preview
PDF (Abstract) - Accepted Version
145Kb
[img]
Preview
PDF (Chapter 1) - Accepted Version
147Kb
[img]
Preview
PDF (References) - Accepted Version
138Kb

Official URL: http://iportal.ump.edu.my/lib/item?id=chamo:45655&...

Abstract

This research focused on the study about the effect of nozzle diameter on jet impingement cooling system. The impinging jet can be described as a phenomenon in which the fluid exiting from a nozzle or orifice hits a wall or solid surface usually at normal angle. Impinging air jets have been widely used in many industrial applications in order to achieve enhanced coefficients for convective heating, cooling or drying. A single air jet or arrays of air jets, impinging normally on a surface are an effective method to enhance heat and mass transfer. Engineering applications that widely use air jets include cooling of hot steel plates, tempering of glass plates, drying of textiles and paper, cooling of turbine blades, electronic components and de-icing of aircraft. Experiments were conducted to determine the effect of nozzle diameter on the heat transfer coefficients from a small heat source to a jet impingement cooling system, submerged and confined air. The experiment were carried out with a single jet with three different nozzle diameter, d; 0.5, 1.0, 2.0 cm and four dimensionless jet to heat source spacing, S/d (6, 8, 10, 12) were tested within the laminar jet Reynolds number ranging from 500-2300. The results indicate that the heat transfer coefficient, h increase with the increasing nozzle diameter at the stagnation point region corresponding to 0< r/d <4. This may be attributed to an increase in the jet momentum and turbulence intensity level with the larger nozzle diameter, which results in the heat transfer augmentation. However, the effect of the nozzle diameter on the Nusselt numbers does not exist at the wall jet region corresponding to r/d>4. This may be attributed to the fact that the impinging jet flow characteristics are almost lost in the process of the re-development of the boundary layer after the jet impinges on the plate. By the increasing of the heat transfer coefficient, h the local Nusselt number, Nu also will be increase. This research are significant to improve the overheat component and devices problem nowadays. The results can also significantly increase the performance of the needed component in order to improve product reliability and customer satisfactions.

Item Type:Undergraduates Project Papers
Additional Information:Project paper (Bachelor of Mechanical Engineering) -- Universiti Malaysia Pahang - 2009, SV: Wan Azmi Bin Wan Hamzah
Uncontrolled Keywords:Heat; Transmission; Nozzles
Subjects:T Technology > TJ Mechanical engineering and machinery
Divisions:Faculty of Mechanical Engineering
ID Code:870
Deposited By: Rosfadilla Mohamad Zainun
Deposited On:30 Sep 2010 16:48
Last Modified:05 Apr 2017 13:41

Repository Staff Only: item control page

 

 

 

 

 

 

Introduction

An Institutional Repository is an online focus for collecting, preserving, and disseminating any University publication in the digital form for the intellectual sharing.
The UMP Institutional Repository (UMP IR) provides access of University publication such as journal article, conference paper, research paper, thesis and dissertations.


Any Enquiries

Please email or call Knowledge Management staff:-

Pn. Noorul Farina (09-424 5605) OR
Cik Ratna Wilis Haryati (09-424 5612)

Any correspondence concerning this specific repository should be sent to umplibrary@ump.edu.my